User Tools

Site Tools


stanton_scs.3m

Differences

This shows you the differences between two versions of the page.

Link to this comparison view

Both sides previous revision Previous revision
stanton_scs.3m [2015/08/02 03:10]
be.ing
stanton_scs.3m [2015/11/26 22:06] (current)
be.ing move new content on separate user guide page here
Line 5: Line 5:
   *[[http://​www.stantondj.com/​stanton-controllers-systems/​scs3m.html|Manufacturer'​s product page]]   *[[http://​www.stantondj.com/​stanton-controllers-systems/​scs3m.html|Manufacturer'​s product page]]
  
-====== ​Mapping ​description ======+====== ​Default mapping ​description ====== 
 + 
 +This guide explains how the SCS.3m is mapped by default in Mixxx. 
 + 
 +{{:​hardware:​stantonscs:​scs3m_main.png |}}
  
 The left side of the controller controls deck 1. The right side is for deck 2. We'll walk through the controller from top to bottom and explain the features. The left side of the controller controls deck 1. The right side is for deck 2. We'll walk through the controller from top to bottom and explain the features.
Line 66: Line 70:
   * Needle drop function: Hold a Deck button to use the cross-fader strip to search through the track loaded on that deck   * Needle drop function: Hold a Deck button to use the cross-fader strip to search through the track loaded on that deck
  
-===== VU Meters =====+===== Level Meters =====
  
-These normally show the pre-fader signal for the respective deck. +These normally show the pre-fader signal for the respective deck. When holding down the Master button, they show the stereo master output meters: left side for the left channel, right side for the right channel.
-  * When holding down the Master button, they show the stereo master output meters: left side for the left channel, right side for the right channel.+
  
 **NOTE:** The LEDs are calibrated to the VU meters on-screen. If you see a red LED flicker, __you are clipping__ and need to reduce the volume or gain to avoid distorted sound and/or speaker damage. **NOTE:** The LEDs are calibrated to the VU meters on-screen. If you see a red LED flicker, __you are clipping__ and need to reduce the volume or gain to avoid distorted sound and/or speaker damage.
  
-===== =====+ 
 +====== ​Proposed changes for 2.0 ====== 
 + 
 +This section explains the extensions proposed for Mixxx 2.0.  
 + 
 +===== Deck switching buttons ===== 
 + 
 +When touching the "A C" or "B D" buttons, the mixer switches between decks. 
 +On the left side, touching "A C" will switch between decks 1 and 3. On the right 
 +side, touching "B D" will switch between decks 2 and 4. All controls except for 
 +the crossfader then control the selected deck. 
 + 
 +Connected SCS.3d modules will follow deck changes. For example if you switch from deck 1 to deck 3 on a SCS.3m, all connected SCS.3d modules who are on deck 1 will also switch to deck 3. 
 + 
 + 
 +===== EQ mode ===== 
 + 
 +This is the standard mixing mode where the three EQ sliders control low/​mid/​high. 
 +The top slider controls the filter knob. 
 + 
 +Touching EQ will return to EQ mode from the FX modes. Holding EQ and touching a slider will reset it to its preset position. (Unfortunately this doesn'​t work for FX and MASTER modes.) 
 + 
 +===== FX modes ===== 
 + 
 +Touch one of the four buttons to the side of the gain slider to control one of the effect chains. Top button selects first effect chain and so forth. In this mode, the vertical sliders control the first three knobs of the first effect in the selected effect chain. The top slider controls dry/wet mix. 
 + 
 +You can assign FX chains to the deck by holding FX and pressing one of the four buttons next to the gain slider. So to assign FX chain 1 to the current deck, hold FX and press the top button (right below EQ). 
 + 
 +When holding FX, the volume slider can be used to adjust channel gain. Hold FX and slide up to make the channel louder. Hold FX-EQ and touch the gain slider to reset gain. 
 + 
 +===== MASTER mode ===== 
 + 
 + 
 +When holding the central MASTER button, the left side controls the headphone 
 +channel, while the right side controls the master channel. 
 + 
 +  * Left top slider: Pre/main mix on headphone 
 +  * Right top slider: main balance 
 +  * Left slider: head gain 
 +  * Right slider: master gain 
 +  * Buttons: The buttons assign effects to head and master
  
 //Images courtesy of Stanton Magnetics, Inc.// //Images courtesy of Stanton Magnetics, Inc.//
stanton_scs.3m.txt · Last modified: 2015/11/26 22:06 by be.ing